ODM Non Corrosive Silicone Sealant Window Installation Clear
Quick curingnon corrosive silicone sealant window installation clear silicone
Art No. A0301
1. Fast curing
2. Water/rain resistant
4. both Interior and exterior use
MATERIAL SAFETY DATA SHEET
Section 1: Product & Company Identification
Product Name: SILICONE SEALANT
Product Number: A0301
Manufactured by: Plyfit Industries China, Inc.
Section 2: Composition / Information on Ingredients
Component CAS ACGIH OSHA OTHER %
NUMBER TLV PEL LIMITS
Silica 7631-86-9 NE NE NE 12-15
Methyltriacetoxysilane 4253-34-3 NE NE 10ppm 8 -12
Ethyltriacetoxysilane 17689-77-9 NE NE 10ppm 9-13
Nitrogen 7727-37-9 NE NE NE 2-5
Hydroxy-Terminated 70131-67-8 NE NE NE 45-65
Polydimethylsiloxane 63148-62-9 NE NE NE 7-12
Section 3: Hazards Identification
Odor: Acetic acid odor
Warning: Contents under Pressure, Uncured product may irritate eyes
Potential Health Effects:
Inhalation: Dizziness, nose and throat irritation.
Eyes: Irritation, moderate corneal injury.
Carcinogenicity: OSHA: No IARC: No NTP: No
Chronic Overexposure: None know
Medical Conditions Aggravated by Exposure: None know
Section 4: First Aid Measures
Inhalation: Remove to fresh air. Give artificial respiration if
Eyes: Flush with large amounts of water for 15 minutes.
Skin: Remove contaminated clothing and wash area with soap and
Ingestion: Call a physician. Do not induce vomiting.
Section 5: Fire-Fighting Measures
Flashpoint: NA Method: NA LEL: ND UEL: ND
Extinguishing Media: Water fog, dry chemical and foam
Hazardous Combustion Products: Acetic acid fumes, CO2, SiO2
Fire-fighting Instructions: Remove containers from fire area if
Self-contained breathing apparatus for fire
Fighting. Aerosol cans may explode if heated above
NEPA: Health: 1 Flammability: 1 Reactivity: 0
HMIS: Health: 1 Flammability: 1 Reactivity: 0 PPE: B
Section 6: Accidental Release Measures
Spill/Leak Procedures: Usually not a problem with aerosols. Area
should be ventilated. Absorbent should be used to pick up excess
Section 7: Handling and Storage
Handling Procedures: Store in a cool, dry area. Aerosol cans must
be maintained below 120℉ to prevent cans from exploding.
Section 8: Exposure Controls / Personal Protection
Engineering Controls: Adequate to prevent accumulation of vapors.
Use mechanical means if necessary to maintain levels below the
exposure limits. If working in a confined space, follow applicable
Respiratory: Use NIOSH/MSHA compliant respirators or self-contained
breathing apparatus above exposure limits. Follow OSHA regulations
29 CFR 1910.134.
Protective Clothing/Equipment: Wear chemically protective gloves
and safety glasses. Use a splash apron and boots if splashing
Section 9: Physical & Chemical Properties
Physical State: Paste Appearance & Odor: clear, white, black,
Paste, acetic acid odor
Specific Gravity: 0.97~1.03@25℃ Boiling Point: ND
Freezing Point: ND Vapor Pressure: NA
Evaporation Rate: <1 Vapor Density(air=1) >air
PH: NA Solubility: None in Water
Volatile Organic Compounds %: ND g/L: ND lbs./gal: ND
Section 10: Stability and Reactivity
Chemical Incompatibilities: Strong oxidizers.
Materials to Avoid: Strong oxidizers. Water causes curing.
Hazardous Decomposition Products: None
Section 11: Toxicological Information
Long-term toxicological studies have not been conducted for this
product. See section 3 of this MSDS for acute symptoms of
overexposure and carcinogenicity information.
Section 12: Ecological Information
Ecotoxicity: No data available.
Environmental Fate: No data available for biodegradation
Section 13: Transportation Information
Shipping Name: Consumer Commodity
Hazard Class: ORM-D UN Number: NA Packing Group: NA
Label: NA Placard: NA Special Provisions: NA
Section 14: Disposal Considerations
Disposal: This material if discarded may be hazardous waste,
contact your local or state environmental agency for specific
rules. Do not dump into sewers, on the ground or into any body of
Section 15: Regulatory Information
TSCA: All components are either listed under TSCA or are exempt.
Extremely Hazardous Substances: No
|ART NO.||CONTENT||CAN MATERIALS||CAN SIZE||CARTON SIZE||PACKING||20’GP|
Shelf Life: 12 months
- Silicone Sealant should be applied when room is sufficiently
- Avoid contact with eyes.
- KEEP IT OUT OF REACH OF CHILDREN;
- Store it in cool, dry and well-ventilated place below 27 degrees
- Keep away from fire source;
All of our products comply with international quality standards and
are greatly appreciated in a variety of markets throughout the
world. Our company always holds the managerial idea that “Quality
Proves Strength, Details Reach to Success.” If you are interested
in any of our products, please feel free to contact us. We are
looking forward to forming successful business relationships with
new clients around the world.
Q1: Can I get some samples? A: Yes, sample order is available for quality check and market
test. But you have to pay the sample cost and express cost. Q2: Do you receive customized order? A: Yes, ODM & OEM are welcomed. Q3: What's the lead time? A: According to the order quantity, small order usually need 3-5
days, big order need negotiation. Q4: What's your warranty terms? A: We supply 12 months warranty time. Q5: What's your payment terms? A: We receive Escrow, T/T, West Union, Cash and etc.
A. All surface must be clean and dry, degrease and wash off any
contaminates that could impair adhesion.
B.Certain plastic may require specific surface treatment to obtain
optimum adhesion. Such as the polypropylene, which should need
chemical corrosion or plasma treatments?
How to apply
A. Apply a bead of neutral sealant to one of the prepared surface,
and then quickly cover with the other substrate to be bonded.
B. On exposure to moisture, the freshly applied material will “skin
over” in about 10 to 15 minutes at room temperature and 50%
relative humidity. The surface is easily tooled with a spatula.
Why choose us:
1. Over 13 years manufacturing experience;
2. 11 years golden supplier on Alibaba.com;
3. Exporting experience in over 80 countries;
4. Quality Guarantee: ISO9001,REACH,TUV, Factory Audit, SASO;
5. On time delivery, professional R&D team & satisfied
6. Customized product available.